Products

Our product development takes place in top professional
R&D-departments, where our engineers are always working
to develop new innovative products in co-operation with our customers.

MU 807-XG/...

Unity Gain ¼ λ Mobile Antenna for the 800 MHz band width GPS

  • External antenna whip mounted on the XG-COMBI mount.
    • Silicone covered flexibe steel wire whip.
    • Two models:
      MU 807-XG/l: 768 - 806 MHz
      MU 807-XG/h: 806 - 869 MHz

DESCRIPTION

  • Stainless steel XG-COMBI mount with M6-thread whip-fastening system.
  • Choose between mount with FME-connection (without cable) or model with permanently attached 4 m cable with FME connector.
  • Easily removable whip for car wash.
  • GPS-antenna for fixed installations.
    • Full hemispherical coverage.
    • Built-in high-gain, low-noise amplifier.
    • Right-Hand Circular Polarization (RHCP).
    • 2.85 V - 5 V supply voltage (typical 3 V).

The whip is compatible with all below mounts

ORDERING DESIGNATIONS

TYPE FREQUENCY MOUNT VERSION PRODUCT NO.
MU 807-XG/l 768 - 806 MHz XG-COMBI mount
(oblong) with
FME-system
130002081
MU 807-XG/h 806 - 869 MHz Same mount as above 130002082
MU 807-XGP4/l 768 - 806 MHz XGP4-COMBI mount
(oblong) with 4 m cable
+ FME-system
130002083
MU 807-XGP4/h 806 - 869 MHz Same mount as above 130002084

SPECIFICATIONS

ELECTRICAL  
MODEL MU 807-XG/...
ANTENNA TYPE ¼ λ mobile antenna
FREQUENCY 800 MHz-band covered by two models
IMPEDANCE Nom. 50 Ω
POLARIZATION Vertical
GAIN 0 dB (acc. to EIA RS-329-1)
BANDWIDTH > 80 MHz @ SWR ≤ 1.5
> 140 MHz @ SWR ≤ 2.0
SWR ≤ 1.2 @ f. res.
MAX. POWER 60 W
MECHANICAL  
MATERIALS Whip:
Steel wire covered with silicone tubing
Black-chromed brass
Mount:
Black-chromed brass
Weather- and shockproof plastics
Stainless steel
RECOMMENDED
INSTALLATION
TORQUE
4 ± 1 Nm
COLOUR Black
HEIGHT Approx. 100 mm
WEIGHT XG-version: Approx. 70 g
XGP4-version: Approx. 210 g
MOUNTING 19 mm dia. hole
ELECTRICAL for GPS-part
OPERATING FREQUENCY 1575.42 ±1.023 MHz
LNA GAIN 22 dB ±2 dB
NOISE FIGURE Max. 1.5 dB (typical 1.1 dB)
VOLTAGE DC 2.85 V ~ 5 V (typical 3 V)
CURRENT ≤ 20 mA
IMPEDANCE Nom. 50 Ω
MECHANICAL
CONNECTOR Cable: RG 178, length 150 mm
Connector: FME-male

INSTALLATION

The XG-antenna types can be mounted anywhere on the car, however, roof top mounting is always recommended.

The oblong XG-COMBI mount can be mounted on the often very narrow strip on the rear wing between the hatch and the side of the car.

Mounting can take place with access from the outside or inside when drilling an 19 mm dia. hole.

When cleaning the car in car-washing machines, remove the whip using a spanner, size 9 mm. After wash, refit the whip and tighten it lightly with the spanner.

As the XG-COMBI mount is internally equipped with a bendable section, the antenna can always be adjusted to an upright position independent of the tilt angle of the installation spot.

 

1. INSTALLATION DIMENSIONS

 

2. INSTALLATION STEPS

Do not use sealer on rubber gasket or other places.

 

ASSEMBLY INSTRUCTIONS

  1. Put GPS-FME-connector-cable through the gasket (2).
  2. Put the gasket (2) + GPS-part (1) over the body (B).
  3. Put the body (B) + gasket (3) + GPS-part (1) through the ø19 mm hole.
  4. Put the housing (4) over the body (B) and be sure that the GPS-part (1) fits into the square hole in the body (B).
  5. Put the threaded part over the body (B) and tighten max. 4 ±1 Nm!.
  6. Put the corrugated plastic unit (6) over the body (B).
  7. Mount the antenna whip se figure 4.

See what we are up to

Connect with us online, to get latest news

and see where the next exhibition is going to take place

Exhibition Calendar

  • PMRExpo 2018

    PMRExpo 2018 27-29 November 2018, Cologne. Procom will participate on PMRExpo. The leading European trade…
    Read More

We are Social

APN Logo Blue