Products

Our product development takes place in top professional
R&D-departments, where our engineers are always working
to develop new innovative products in co-operation with our customers.

XG-Combi Mount

GPS mount for GPS Antennas and Other Frequencies

  • Mobile mount with a nice, “streamline”-look, which can be installed everywhere on the car in an 19 mm dia. hole.
  • Especially suited for mounting on the narrow strip on rear wing between trunk lid and car side.
  • M6 thread whip-mounting system.

DESCRIPTION

  • Very low requirements to installation depth both under and after installation.
  • Designed for installation with access from the outside only.
  • Bendable section in mount makes whip tiltable 30° by hand.
  • Complete line of whips available for all communications bands up to 1300 MHz.
  • Mounting body made of stainless steel !
  • Choice between two connection principles:
    • XG-Combi mount: FME-connection and GPS (supplied without cable).
    • XGP4-Combi mount: Permanently attached 4 m RG 58 cable terminated with FME-connector and GPS.
  • GPS-antenna for fixed installations.
    • Full hemispherical coverage.
    • Built-in high-gain, low-noise amplifier.
    • Right-Hand Circular Polarization (RHCP).
    • 2.85 V - 5 V supply voltage (typical 3 V).

ORDERING DESIGNATIONS

TYPE NO. VERSION PRODUCT NO.
XG-COMBI MOUNT XG-Combi mount with FME-system 130002032
XGP4-COMBI MOUNT XGP4-Combi mount with 4 m RG 58
cable and FME-connector
130002043

 

A SELECTION OF THE VARIOUS WHIPS WHICH CAN BE CONNECTED TO THE XG-COMBI MOUNT

SPECIFICATIONS

ELECTRICAL
MODEL XG-COMBI MOUNT
APPLICATION Mount for mobile antennas
CONNECTION TO WHIP M6 thread stud
BUILD-IN DEPTH Active : 30 mm
Passive : 11 mm
MECHANICAL
MATERIALS Black-chromed brass
Weather- and shockproof plastics
Stainless steel
RECOMMENDED
INSTALLATION
TORQUE
4 ± 1 Nm
COLOUR Black
LENGTH/WIDTH 48 mm/28 mm
WEIGHT XG-version: Approx. 60 g
XGP4-version: Approx. 200 g
MOUNTING 19 mm dia. hole
ROOF THICKNESS Max. 2 mm
ELECTRICAL for GPS-part
OPERATING FREQUENCY 1575.42 ±1.023 MHz
LNA GAIN 22 dB ±2 dB
NOISE FIGURE Max. 1.5 dB (typical 1.1 dB)
VOLTAGE DC 2.85 V ~ 5 V (typical 3 V)
CURRENT ≤ 20 mA
IMPEDANCE Nom. 50 Ω
MECHANICAL
CONNECTOR Cable: RG 178, length 150 mm
Connector: FME-male

FME-SYSTEM ACCESSORIES

FME-CABLES
TYPE PRODUCT NO.
1 m FME 130000437
2 m FME 130000447
3 m FME 130000457
4 m FME 130000466
5 m FME 130000474
6 m FME 130000483
4 m FME-white 110000064
6 m FME-white 110000066
12 m FME-white 110000068
18 m FME-white 110000069
FME-CONNECTORS
TYPE PRODUCT NO.
FME-FME 130000583
FME-P
(Prolongation)
130000565
FME-N 130000571
FME-FSMA
(Female-SMA)
130000578
FME-BNC 130000566
FME-TNC 130000569
FME-UHF 130000572
FME-MUHF
(Mini-UHF)
130000573
FME-EMUHF
(Elbow-MUHF)
130000582
FME-EBNC
(Elbow-BNC)
130000580
FME-ETNC
(Elbow-TNC)
130000581
FME-SMA 130000577

 

For further information about other types of FME-cables and FME-connectors, please compare the cable and connector data sheets under accessories in our catalogue.

INSTALLATION

XG-Combi mount antenna types can be mounted anywhere on the car, however, roof top mounting is always recommended.

The oblong XG-Combi mount is able to be mounted on the often very narrow strip on the rear wing between the trunk lid and the side of the car.

Mounting can take place with access from the outside or inside when drilling an 19 mm dia. hole.

A good contact surface on the inside of the car body must always be ensured, thus enabling the base plate to get in direct contact with the metal parts of the car, which is of utmost importance for proper performance of the antenna.

When cleaning the car in car-washing machines, the whip is easily removed using a fork spanner, size 9 mm. The whip is refitted again by screwing it onto the thread stud and tightening it lightly with the spanner.

As the XG-Combi mount is internally equipped with a bendable section, the antennas can always be adjusted to an upright position independent of the tilt angle of the installation spot (up to 30° tilt).

1. INSTALLATION DIMENSIONS

 

2. INSTALLATION STEPS

 

Do not use sealer on rubber gasket or other places.

 

ASSEMBLY INSTRUCTIONS

  • Put GPS-FME-connector-cable through the gasket (2).
  • Put the gasket (2) + GPS-part (1) over the body (B).
  • Put the body (B) + gasket (3) + GPS-part (1) through the ø19 mm hole.
  • Put the housing (4) over the body (B) and be sure that the GPS-part (1) fits into the square hole in the body (B).
  • Put the threaded part over the body (B) and tighten max. 4 ±1 Nm!
  • Put the corrugated plastic unit (6) over the body (B).
  • Mount the antenna whip se figure 4.

 

See what we are up to

Connect with us online, to get latest news

and see where the next exhibition is going to take place

Exhibition Calendar

We are Social

APN Logo Blue